Iron Craft ’13 #8 – Lego DJ T-Shirt

This week’s Iron Craft challenge was based around toys. I knew right away mine was going to be based on Legos. My husband, Matt, loves his Legos to this day. (You should see his office, it’s all Legos and computers.) He has been collecting minifigs and when he got this DJ one I thought it would be fun to make him a copy of the shirt.
Iron Craft '13 Challenge #8 - Lego DJ T-Shirt
I think it is supposed to be one of those equalizer shirts, but I think it is so funny that the image is in the shape of a Lego minifig head. And here is Matt in his life-sized version.
Iron Craft '13 Challenge #8 - Lego DJ T-Shirt
I used freezer paper to make a stencil for this shirt which is a pretty easy technique. Really the hardest part of this project was drawing up the pattern, but lucky you, I’ve included a download of it in the instructions below.

Lego DJ T-Shirt

Iron Craft '13 Challenge #8 - Lego DJ T-Shirt
Supplies:

  • freezer paper sheets
  • t-shirt (I find fabric paints look best on lighter color t-shirts though there are some specific for using on dark fabric)
  • fabric paint (I used red, orange, lime green and green)
  • piece of paper or cardboard a little bigger than your stencil

Tools:

  • exacto knife
  • ruler
  • iron
  • small, soft paintbrush

1. Download and print out the Lego DJ Pattern onto the dull side (non-wax side) of the freezer paper the size you want for your t-shirt.
Iron Craft '13 Challenge #8 - Lego DJ T-Shirt
Mine is about 8″x 8″.

2. Using the exacto knife and ruler, carefully cut out all the squares in the pattern.
Iron Craft '13 Challenge #8 - Lego DJ T-Shirt

3. Place the pattern, wax-side (shiny) down, where you want it on the t-shirt. Iron onto the shirt.
Iron Craft '13 Challenge #8 - Lego DJ T-Shirt
I like to measure and make sure the stencil is centered and straight then pin it in place before I iron it on.

4. Place a piece of paper or cardboard behind the stencil inside the t-shirt to prevent the paint from soaking through. Paint inside the cut out squares. I find it it best to paint towards the center of each cut-out section and not towards the edge. This helps prevent bleeding under the stencil. Let dry (my paint took about 4 hours to dry).
Iron Craft '13 Challenge #8 - Lego DJ T-Shirt Iron Craft '13 Challenge #8 - Lego DJ T-Shirt
Iron Craft '13 Challenge #8 - Lego DJ T-Shirt Iron Craft '13 Challenge #8 - Lego DJ T-Shirt
I did one color at a time following the pattern on the Lego. Add a second coat if necessary. You don’t want the paint to be too thick or it will crack with wear. A second coat also gives you more chances of paint bleed.

5. Once completely dry, remove the stencil. Follow the directions on your paint to set it. Usually, it requires a certain amount of dry time and some brands call for it to be set with an iron. Every brand is different so make sure to read the instructions.

Give to your favorite Lego fan!
Iron Craft '13 Challenge #8 - Lego DJ T-Shirt

If you are not reading this post in a feed reader or at http://justcraftyenough.com then the site you are reading is illegally publishing copyrighted material. Contact us at justcraftyenough AT yahoo DOT COM. All patterns, text and photographs in this post are the original creations & property of the author unless otherwise noted.
© 2005 – 2013 Kathy Lewinski & Susan Cornish
11 years ago by in Craft Projects , Crafts , Projects | You can follow any responses to this entry through the RSS feed. You can leave a response, or trackback from your own site.
3 Comments to Iron Craft ’13 #8 – Lego DJ T-Shirt
    • Jenny
    • How much did you have to bribe him with to get him to pose for you. The shirt turned out great. I know a few Lego fans in my house who would love that shirt.

Leave a Reply to DrRuss
Cancel reply

* Required